#if !defined(_RADIOLIB_SX126X_COMMANDS_H) #define _RADIOLIB_SX126X_COMMANDS_H #include "../../TypeDef.h" #if !RADIOLIB_EXCLUDE_SX126X // SX126X SPI commands // operational modes commands #define RADIOLIB_SX126X_CMD_NOP 0x00 #define RADIOLIB_SX126X_CMD_SET_SLEEP 0x84 #define RADIOLIB_SX126X_CMD_SET_STANDBY 0x80 #define RADIOLIB_SX126X_CMD_SET_FS 0xC1 #define RADIOLIB_SX126X_CMD_SET_TX 0x83 #define RADIOLIB_SX126X_CMD_SET_RX 0x82 #define RADIOLIB_SX126X_CMD_STOP_TIMER_ON_PREAMBLE 0x9F #define RADIOLIB_SX126X_CMD_SET_RX_DUTY_CYCLE 0x94 #define RADIOLIB_SX126X_CMD_SET_CAD 0xC5 #define RADIOLIB_SX126X_CMD_SET_TX_CONTINUOUS_WAVE 0xD1 #define RADIOLIB_SX126X_CMD_SET_TX_INFINITE_PREAMBLE 0xD2 #define RADIOLIB_SX126X_CMD_SET_REGULATOR_MODE 0x96 #define RADIOLIB_SX126X_CMD_CALIBRATE 0x89 #define RADIOLIB_SX126X_CMD_CALIBRATE_IMAGE 0x98 #define RADIOLIB_SX126X_CMD_SET_PA_CONFIG 0x95 #define RADIOLIB_SX126X_CMD_SET_RX_TX_FALLBACK_MODE 0x93 // register and buffer access commands #define RADIOLIB_SX126X_CMD_WRITE_REGISTER 0x0D #define RADIOLIB_SX126X_CMD_READ_REGISTER 0x1D #define RADIOLIB_SX126X_CMD_WRITE_BUFFER 0x0E #define RADIOLIB_SX126X_CMD_READ_BUFFER 0x1E // DIO and IRQ control #define RADIOLIB_SX126X_CMD_SET_DIO_IRQ_PARAMS 0x08 #define RADIOLIB_SX126X_CMD_GET_IRQ_STATUS 0x12 #define RADIOLIB_SX126X_CMD_CLEAR_IRQ_STATUS 0x02 #define RADIOLIB_SX126X_CMD_SET_DIO2_AS_RF_SWITCH_CTRL 0x9D #define RADIOLIB_SX126X_CMD_SET_DIO3_AS_TCXO_CTRL 0x97 // RF, modulation and packet commands #define RADIOLIB_SX126X_CMD_SET_RF_FREQUENCY 0x86 #define RADIOLIB_SX126X_CMD_SET_PACKET_TYPE 0x8A #define RADIOLIB_SX126X_CMD_GET_PACKET_TYPE 0x11 #define RADIOLIB_SX126X_CMD_SET_TX_PARAMS 0x8E #define RADIOLIB_SX126X_CMD_SET_MODULATION_PARAMS 0x8B #define RADIOLIB_SX126X_CMD_SET_PACKET_PARAMS 0x8C #define RADIOLIB_SX126X_CMD_SET_CAD_PARAMS 0x88 #define RADIOLIB_SX126X_CMD_SET_BUFFER_BASE_ADDRESS 0x8F #define RADIOLIB_SX126X_CMD_SET_LORA_SYMB_NUM_TIMEOUT 0xA0 // status commands #define RADIOLIB_SX126X_CMD_GET_STATUS 0xC0 #define RADIOLIB_SX126X_CMD_GET_RSSI_INST 0x15 #define RADIOLIB_SX126X_CMD_GET_RX_BUFFER_STATUS 0x13 #define RADIOLIB_SX126X_CMD_GET_PACKET_STATUS 0x14 #define RADIOLIB_SX126X_CMD_GET_DEVICE_ERRORS 0x17 #define RADIOLIB_SX126X_CMD_CLEAR_DEVICE_ERRORS 0x07 #define RADIOLIB_SX126X_CMD_GET_STATS 0x10 #define RADIOLIB_SX126X_CMD_RESET_STATS 0x00 #define RADIOLIB_SX126X_CMD_PRAM_UPDATE 0xD9 #define RADIOLIB_SX126X_CMD_SET_LBT_SCAN_PARAMS 0x9A #define RADIOLIB_SX126X_CMD_SET_SPECTR_SCAN_PARAMS 0x9B // SX126X SPI command variables //RADIOLIB_SX126X_CMD_SET_SLEEP MSB LSB DESCRIPTION #define RADIOLIB_SX126X_SLEEP_START_COLD 0b00000000 // 2 2 sleep mode: cold start, configuration is lost (default) #define RADIOLIB_SX126X_SLEEP_START_WARM 0b00000100 // 2 2 warm start, configuration is retained #define RADIOLIB_SX126X_SLEEP_RTC_OFF 0b00000000 // 0 0 wake on RTC timeout: disabled #define RADIOLIB_SX126X_SLEEP_RTC_ON 0b00000001 // 0 0 enabled //RADIOLIB_SX126X_CMD_SET_STANDBY #define RADIOLIB_SX126X_STANDBY_RC 0x00 // 7 0 standby mode: 13 MHz RC oscillator #define RADIOLIB_SX126X_STANDBY_XOSC 0x01 // 7 0 32 MHz crystal oscillator //RADIOLIB_SX126X_CMD_SET_RX #define RADIOLIB_SX126X_RX_TIMEOUT_NONE 0x000000 // 23 0 Rx timeout duration: no timeout (Rx single mode) #define RADIOLIB_SX126X_RX_TIMEOUT_INF 0xFFFFFF // 23 0 infinite (Rx continuous mode) //RADIOLIB_SX126X_CMD_SET_TX #define RADIOLIB_SX126X_TX_TIMEOUT_NONE 0x000000 // 23 0 Tx timeout duration: no timeout (Tx single mode) //RADIOLIB_SX126X_CMD_STOP_TIMER_ON_PREAMBLE #define RADIOLIB_SX126X_STOP_ON_PREAMBLE_OFF 0x00 // 7 0 stop timer on: sync word or header (default) #define RADIOLIB_SX126X_STOP_ON_PREAMBLE_ON 0x01 // 7 0 preamble detection //RADIOLIB_SX126X_CMD_SET_REGULATOR_MODE #define RADIOLIB_SX126X_REGULATOR_LDO 0x00 // 7 0 set regulator mode: LDO (default) #define RADIOLIB_SX126X_REGULATOR_DC_DC 0x01 // 7 0 DC-DC //RADIOLIB_SX126X_CMD_CALIBRATE #define RADIOLIB_SX126X_CALIBRATE_IMAGE_OFF 0b00000000 // 6 6 image calibration: disabled #define RADIOLIB_SX126X_CALIBRATE_IMAGE_ON 0b01000000 // 6 6 enabled #define RADIOLIB_SX126X_CALIBRATE_ADC_BULK_P_OFF 0b00000000 // 5 5 ADC bulk P calibration: disabled #define RADIOLIB_SX126X_CALIBRATE_ADC_BULK_P_ON 0b00100000 // 5 5 enabled #define RADIOLIB_SX126X_CALIBRATE_ADC_BULK_N_OFF 0b00000000 // 4 4 ADC bulk N calibration: disabled #define RADIOLIB_SX126X_CALIBRATE_ADC_BULK_N_ON 0b00010000 // 4 4 enabled #define RADIOLIB_SX126X_CALIBRATE_ADC_PULSE_OFF 0b00000000 // 3 3 ADC pulse calibration: disabled #define RADIOLIB_SX126X_CALIBRATE_ADC_PULSE_ON 0b00001000 // 3 3 enabled #define RADIOLIB_SX126X_CALIBRATE_PLL_OFF 0b00000000 // 2 2 PLL calibration: disabled #define RADIOLIB_SX126X_CALIBRATE_PLL_ON 0b00000100 // 2 2 enabled #define RADIOLIB_SX126X_CALIBRATE_RC13M_OFF 0b00000000 // 1 1 13 MHz RC osc. calibration: disabled #define RADIOLIB_SX126X_CALIBRATE_RC13M_ON 0b00000010 // 1 1 enabled #define RADIOLIB_SX126X_CALIBRATE_RC64K_OFF 0b00000000 // 0 0 64 kHz RC osc. calibration: disabled #define RADIOLIB_SX126X_CALIBRATE_RC64K_ON 0b00000001 // 0 0 enabled #define RADIOLIB_SX126X_CALIBRATE_ALL 0b01111111 // 6 0 calibrate all blocks //RADIOLIB_SX126X_CMD_CALIBRATE_IMAGE #define RADIOLIB_SX126X_CAL_IMG_430_MHZ_1 0x6B #define RADIOLIB_SX126X_CAL_IMG_430_MHZ_2 0x6F #define RADIOLIB_SX126X_CAL_IMG_470_MHZ_1 0x75 #define RADIOLIB_SX126X_CAL_IMG_470_MHZ_2 0x81 #define RADIOLIB_SX126X_CAL_IMG_779_MHZ_1 0xC1 #define RADIOLIB_SX126X_CAL_IMG_779_MHZ_2 0xC5 #define RADIOLIB_SX126X_CAL_IMG_863_MHZ_1 0xD7 #define RADIOLIB_SX126X_CAL_IMG_863_MHZ_2 0xDB #define RADIOLIB_SX126X_CAL_IMG_902_MHZ_1 0xE1 #define RADIOLIB_SX126X_CAL_IMG_902_MHZ_2 0xE9 #define RADIOLIB_SX126X_CAL_IMG_FREQ_TRIG_MHZ (20.0f) //RADIOLIB_SX126X_CMD_SET_PA_CONFIG #define RADIOLIB_SX126X_PA_CONFIG_HP_MAX 0x07 #define RADIOLIB_SX126X_PA_CONFIG_PA_LUT 0x01 #define RADIOLIB_SX126X_PA_CONFIG_SX1262_8 0x00 //RADIOLIB_SX126X_CMD_SET_RX_TX_FALLBACK_MODE #define RADIOLIB_SX126X_RX_TX_FALLBACK_MODE_FS 0x40 // 7 0 after Rx/Tx go to: FS mode #define RADIOLIB_SX126X_RX_TX_FALLBACK_MODE_STDBY_XOSC 0x30 // 7 0 standby with crystal oscillator #define RADIOLIB_SX126X_RX_TX_FALLBACK_MODE_STDBY_RC 0x20 // 7 0 standby with RC oscillator (default) //RADIOLIB_SX126X_CMD_SET_DIO_IRQ_PARAMS #define RADIOLIB_SX126X_IRQ_LR_FHSS_HOP 0b0100000000000000 // 14 14 PA ramped up during LR-FHSS hop #define RADIOLIB_SX126X_IRQ_TIMEOUT 0b0000001000000000 // 9 9 Rx or Tx timeout #define RADIOLIB_SX126X_IRQ_CAD_DETECTED 0b0000000100000000 // 8 8 channel activity detected #define RADIOLIB_SX126X_IRQ_CAD_DONE 0b0000000010000000 // 7 7 channel activity detection finished #define RADIOLIB_SX126X_IRQ_CRC_ERR 0b0000000001000000 // 6 6 wrong CRC received #define RADIOLIB_SX126X_IRQ_HEADER_ERR 0b0000000000100000 // 5 5 LoRa header CRC error #define RADIOLIB_SX126X_IRQ_HEADER_VALID 0b0000000000010000 // 4 4 valid LoRa header received #define RADIOLIB_SX126X_IRQ_SYNC_WORD_VALID 0b0000000000001000 // 3 3 valid sync word detected #define RADIOLIB_SX126X_IRQ_PREAMBLE_DETECTED 0b0000000000000100 // 2 2 preamble detected #define RADIOLIB_SX126X_IRQ_RX_DONE 0b0000000000000010 // 1 1 packet received #define RADIOLIB_SX126X_IRQ_TX_DONE 0b0000000000000001 // 0 0 packet transmission completed #define RADIOLIB_SX126X_IRQ_ALL 0b0100001111111111 // 14 0 all interrupts #define RADIOLIB_SX126X_IRQ_NONE 0b0000000000000000 // 14 0 no interrupts //RADIOLIB_SX126X_CMD_SET_DIO2_AS_RF_SWITCH_CTRL #define RADIOLIB_SX126X_DIO2_AS_IRQ 0x00 // 7 0 DIO2 configuration: IRQ #define RADIOLIB_SX126X_DIO2_AS_RF_SWITCH 0x01 // 7 0 RF switch control //RADIOLIB_SX126X_CMD_SET_DIO3_AS_TCXO_CTRL #define RADIOLIB_SX126X_DIO3_OUTPUT_1_6 0x00 // 7 0 DIO3 voltage output for TCXO: 1.6 V #define RADIOLIB_SX126X_DIO3_OUTPUT_1_7 0x01 // 7 0 1.7 V #define RADIOLIB_SX126X_DIO3_OUTPUT_1_8 0x02 // 7 0 1.8 V #define RADIOLIB_SX126X_DIO3_OUTPUT_2_2 0x03 // 7 0 2.2 V #define RADIOLIB_SX126X_DIO3_OUTPUT_2_4 0x04 // 7 0 2.4 V #define RADIOLIB_SX126X_DIO3_OUTPUT_2_7 0x05 // 7 0 2.7 V #define RADIOLIB_SX126X_DIO3_OUTPUT_3_0 0x06 // 7 0 3.0 V #define RADIOLIB_SX126X_DIO3_OUTPUT_3_3 0x07 // 7 0 3.3 V //RADIOLIB_SX126X_CMD_SET_PACKET_TYPE #define RADIOLIB_SX126X_PACKET_TYPE_GFSK 0x00 // 7 0 packet type: GFSK #define RADIOLIB_SX126X_PACKET_TYPE_LORA 0x01 // 7 0 LoRa #define RADIOLIB_SX126X_PACKET_TYPE_BPSK 0x02 // 7 0 BPSK #define RADIOLIB_SX126X_PACKET_TYPE_LR_FHSS 0x03 // 7 0 LR-FHSS //RADIOLIB_SX126X_CMD_SET_TX_PARAMS #define RADIOLIB_SX126X_PA_RAMP_10U 0x00 // 7 0 ramp time: 10 us #define RADIOLIB_SX126X_PA_RAMP_20U 0x01 // 7 0 20 us #define RADIOLIB_SX126X_PA_RAMP_40U 0x02 // 7 0 40 us #define RADIOLIB_SX126X_PA_RAMP_80U 0x03 // 7 0 80 us #define RADIOLIB_SX126X_PA_RAMP_200U 0x04 // 7 0 200 us #define RADIOLIB_SX126X_PA_RAMP_800U 0x05 // 7 0 800 us #define RADIOLIB_SX126X_PA_RAMP_1700U 0x06 // 7 0 1700 us #define RADIOLIB_SX126X_PA_RAMP_3400U 0x07 // 7 0 3400 us //RADIOLIB_SX126X_CMD_SET_MODULATION_PARAMS #define RADIOLIB_SX126X_GFSK_FILTER_NONE 0x00 // 7 0 GFSK filter: none #define RADIOLIB_SX126X_GFSK_FILTER_GAUSS_0_3 0x08 // 7 0 Gaussian, BT = 0.3 #define RADIOLIB_SX126X_GFSK_FILTER_GAUSS_0_5 0x09 // 7 0 Gaussian, BT = 0.5 #define RADIOLIB_SX126X_GFSK_FILTER_GAUSS_0_7 0x0A // 7 0 Gaussian, BT = 0.7 #define RADIOLIB_SX126X_GFSK_FILTER_GAUSS_1 0x0B // 7 0 Gaussian, BT = 1 #define RADIOLIB_SX126X_GFSK_RX_BW_4_8 0x1F // 7 0 GFSK Rx bandwidth: 4.8 kHz #define RADIOLIB_SX126X_GFSK_RX_BW_5_8 0x17 // 7 0 5.8 kHz #define RADIOLIB_SX126X_GFSK_RX_BW_7_3 0x0F // 7 0 7.3 kHz #define RADIOLIB_SX126X_GFSK_RX_BW_9_7 0x1E // 7 0 9.7 kHz #define RADIOLIB_SX126X_GFSK_RX_BW_11_7 0x16 // 7 0 11.7 kHz #define RADIOLIB_SX126X_GFSK_RX_BW_14_6 0x0E // 7 0 14.6 kHz #define RADIOLIB_SX126X_GFSK_RX_BW_19_5 0x1D // 7 0 19.5 kHz #define RADIOLIB_SX126X_GFSK_RX_BW_23_4 0x15 // 7 0 23.4 kHz #define RADIOLIB_SX126X_GFSK_RX_BW_29_3 0x0D // 7 0 29.3 kHz #define RADIOLIB_SX126X_GFSK_RX_BW_39_0 0x1C // 7 0 39.0 kHz #define RADIOLIB_SX126X_GFSK_RX_BW_46_9 0x14 // 7 0 46.9 kHz #define RADIOLIB_SX126X_GFSK_RX_BW_58_6 0x0C // 7 0 58.6 kHz #define RADIOLIB_SX126X_GFSK_RX_BW_78_2 0x1B // 7 0 78.2 kHz #define RADIOLIB_SX126X_GFSK_RX_BW_93_8 0x13 // 7 0 93.8 kHz #define RADIOLIB_SX126X_GFSK_RX_BW_117_3 0x0B // 7 0 117.3 kHz #define RADIOLIB_SX126X_GFSK_RX_BW_156_2 0x1A // 7 0 156.2 kHz #define RADIOLIB_SX126X_GFSK_RX_BW_187_2 0x12 // 7 0 187.2 kHz #define RADIOLIB_SX126X_GFSK_RX_BW_234_3 0x0A // 7 0 234.3 kHz #define RADIOLIB_SX126X_GFSK_RX_BW_312_0 0x19 // 7 0 312.0 kHz #define RADIOLIB_SX126X_GFSK_RX_BW_373_6 0x11 // 7 0 373.6 kHz #define RADIOLIB_SX126X_GFSK_RX_BW_467_0 0x09 // 7 0 467.0 kHz #define RADIOLIB_SX126X_LORA_BW_7_8 0x00 // 7 0 LoRa bandwidth: 7.8 kHz #define RADIOLIB_SX126X_LORA_BW_10_4 0x08 // 7 0 10.4 kHz #define RADIOLIB_SX126X_LORA_BW_15_6 0x01 // 7 0 15.6 kHz #define RADIOLIB_SX126X_LORA_BW_20_8 0x09 // 7 0 20.8 kHz #define RADIOLIB_SX126X_LORA_BW_31_25 0x02 // 7 0 31.25 kHz #define RADIOLIB_SX126X_LORA_BW_41_7 0x0A // 7 0 41.7 kHz #define RADIOLIB_SX126X_LORA_BW_62_5 0x03 // 7 0 62.5 kHz #define RADIOLIB_SX126X_LORA_BW_125_0 0x04 // 7 0 125.0 kHz #define RADIOLIB_SX126X_LORA_BW_250_0 0x05 // 7 0 250.0 kHz #define RADIOLIB_SX126X_LORA_BW_500_0 0x06 // 7 0 500.0 kHz #define RADIOLIB_SX126X_LORA_CR_4_5 0x01 // 7 0 LoRa coding rate: 4/5 #define RADIOLIB_SX126X_LORA_CR_4_6 0x02 // 7 0 4/6 #define RADIOLIB_SX126X_LORA_CR_4_7 0x03 // 7 0 4/7 #define RADIOLIB_SX126X_LORA_CR_4_8 0x04 // 7 0 4/8 #define RADIOLIB_SX126X_LORA_CR_4_5_LI 0x05 // 7 0 4/5, long interleaver #define RADIOLIB_SX126X_LORA_CR_4_6_LI 0x06 // 7 0 4/6, long interleaver #define RADIOLIB_SX126X_LORA_CR_4_8_LI 0x07 // 7 0 4/8, long interleaver #define RADIOLIB_SX126X_LORA_LOW_DATA_RATE_OPTIMIZE_OFF 0x00 // 7 0 LoRa low data rate optimization: disabled #define RADIOLIB_SX126X_LORA_LOW_DATA_RATE_OPTIMIZE_ON 0x01 // 7 0 enabled #define RADIOLIB_SX126X_BPSK_PULSE_SHAPE 0x16 // 7 0 BSPK pulse shape double OSR, RRC, BT=0.7 //RADIOLIB_SX126X_CMD_SET_PACKET_PARAMS #define RADIOLIB_SX126X_GFSK_PREAMBLE_DETECT_OFF 0x00 // 7 0 GFSK minimum preamble length before reception starts: detector disabled #define RADIOLIB_SX126X_GFSK_PREAMBLE_DETECT_8 0x04 // 7 0 8 bits #define RADIOLIB_SX126X_GFSK_PREAMBLE_DETECT_16 0x05 // 7 0 16 bits #define RADIOLIB_SX126X_GFSK_PREAMBLE_DETECT_24 0x06 // 7 0 24 bits #define RADIOLIB_SX126X_GFSK_PREAMBLE_DETECT_32 0x07 // 7 0 32 bits #define RADIOLIB_SX126X_GFSK_ADDRESS_FILT_OFF 0x00 // 7 0 GFSK address filtering: disabled #define RADIOLIB_SX126X_GFSK_ADDRESS_FILT_NODE 0x01 // 7 0 node only #define RADIOLIB_SX126X_GFSK_ADDRESS_FILT_NODE_BROADCAST 0x02 // 7 0 node and broadcast #define RADIOLIB_SX126X_GFSK_PACKET_FIXED 0x00 // 7 0 GFSK packet type: fixed (payload length known in advance to both sides) #define RADIOLIB_SX126X_GFSK_PACKET_VARIABLE 0x01 // 7 0 variable (payload length added to packet) #define RADIOLIB_SX126X_GFSK_CRC_OFF 0x01 // 7 0 GFSK packet CRC: disabled #define RADIOLIB_SX126X_GFSK_CRC_1_BYTE 0x00 // 7 0 1 byte #define RADIOLIB_SX126X_GFSK_CRC_2_BYTE 0x02 // 7 0 2 byte #define RADIOLIB_SX126X_GFSK_CRC_1_BYTE_INV 0x04 // 7 0 1 byte, inverted #define RADIOLIB_SX126X_GFSK_CRC_2_BYTE_INV 0x06 // 7 0 2 byte, inverted #define RADIOLIB_SX126X_GFSK_WHITENING_OFF 0x00 // 7 0 GFSK data whitening: disabled #define RADIOLIB_SX126X_GFSK_WHITENING_ON 0x01 // 7 0 enabled #define RADIOLIB_SX126X_LORA_HEADER_EXPLICIT 0x00 // 7 0 LoRa header mode: explicit #define RADIOLIB_SX126X_LORA_HEADER_IMPLICIT 0x01 // 7 0 implicit #define RADIOLIB_SX126X_LORA_CRC_OFF 0x00 // 7 0 LoRa CRC mode: disabled #define RADIOLIB_SX126X_LORA_CRC_ON 0x01 // 7 0 enabled #define RADIOLIB_SX126X_LORA_IQ_STANDARD 0x00 // 7 0 LoRa IQ setup: standard #define RADIOLIB_SX126X_LORA_IQ_INVERTED 0x01 // 7 0 inverted #define RADIOLIB_SX126X_BPSK_RAMP_UP_TIME_NONE 0x0000 // 15 0 BPSK ramp-up time optimization: none #define RADIOLIB_SX126X_BPSK_RAMP_UP_TIME_100_BPS 0x370F // 15 0 for 100 bps #define RADIOLIB_SX126X_BPSK_RAMP_UP_TIME_600_BPS 0x092F // 15 0 for 600 bps #define RADIOLIB_SX126X_BPSK_RAMP_DOWN_TIME_NONE 0x0000 // 15 0 BPSK ramp-down time optimization: none #define RADIOLIB_SX126X_BPSK_RAMP_DOWN_TIME_100_BPS 0x1D70 // 15 0 for 100 bps #define RADIOLIB_SX126X_BPSK_RAMP_DOWN_TIME_600_BPS 0x04E1 // 15 0 for 600 bps //RADIOLIB_SX126X_CMD_SET_CAD_PARAMS #define RADIOLIB_SX126X_CAD_ON_1_SYMB 0x00 // 7 0 number of symbols used for CAD: 1 #define RADIOLIB_SX126X_CAD_ON_2_SYMB 0x01 // 7 0 2 #define RADIOLIB_SX126X_CAD_ON_4_SYMB 0x02 // 7 0 4 #define RADIOLIB_SX126X_CAD_ON_8_SYMB 0x03 // 7 0 8 #define RADIOLIB_SX126X_CAD_ON_16_SYMB 0x04 // 7 0 16 #define RADIOLIB_SX126X_CAD_GOTO_STDBY 0x00 // 7 0 after CAD is done, always go to STDBY_RC mode #define RADIOLIB_SX126X_CAD_GOTO_RX 0x01 // 7 0 after CAD is done, go to Rx mode if activity is detected #define RADIOLIB_SX126X_CAD_PARAM_DEFAULT 0xFF // 7 0 used by the CAD methods to specify default parameter value #define RADIOLIB_SX126X_CAD_PARAM_DET_MIN 10 // 7 0 default detMin CAD parameter //RADIOLIB_SX126X_CMD_GET_STATUS #define RADIOLIB_SX126X_STATUS_MODE_STDBY_RC 0b00100000 // 6 4 current chip mode: STDBY_RC #define RADIOLIB_SX126X_STATUS_MODE_STDBY_XOSC 0b00110000 // 6 4 STDBY_XOSC #define RADIOLIB_SX126X_STATUS_MODE_FS 0b01000000 // 6 4 FS #define RADIOLIB_SX126X_STATUS_MODE_RX 0b01010000 // 6 4 RX #define RADIOLIB_SX126X_STATUS_MODE_TX 0b01100000 // 6 4 TX #define RADIOLIB_SX126X_STATUS_DATA_AVAILABLE 0b00000100 // 3 1 command status: packet received and data can be retrieved #define RADIOLIB_SX126X_STATUS_CMD_TIMEOUT 0b00000110 // 3 1 SPI command timed out #define RADIOLIB_SX126X_STATUS_CMD_INVALID 0b00001000 // 3 1 invalid SPI command #define RADIOLIB_SX126X_STATUS_CMD_FAILED 0b00001010 // 3 1 SPI command failed to execute #define RADIOLIB_SX126X_STATUS_TX_DONE 0b00001100 // 3 1 packet transmission done #define RADIOLIB_SX126X_STATUS_SPI_FAILED 0b11111111 // 7 0 SPI transaction failed //RADIOLIB_SX126X_CMD_GET_PACKET_STATUS #define RADIOLIB_SX126X_GFSK_RX_STATUS_PREAMBLE_ERR 0b10000000 // 7 7 GFSK Rx status: preamble error #define RADIOLIB_SX126X_GFSK_RX_STATUS_SYNC_ERR 0b01000000 // 6 6 sync word error #define RADIOLIB_SX126X_GFSK_RX_STATUS_ADRS_ERR 0b00100000 // 5 5 address error #define RADIOLIB_SX126X_GFSK_RX_STATUS_CRC_ERR 0b00010000 // 4 4 CRC error #define RADIOLIB_SX126X_GFSK_RX_STATUS_LENGTH_ERR 0b00001000 // 3 3 length error #define RADIOLIB_SX126X_GFSK_RX_STATUS_ABORT_ERR 0b00000100 // 2 2 abort error #define RADIOLIB_SX126X_GFSK_RX_STATUS_PACKET_RECEIVED 0b00000010 // 2 2 packet received #define RADIOLIB_SX126X_GFSK_RX_STATUS_PACKET_SENT 0b00000001 // 2 2 packet sent //RADIOLIB_SX126X_CMD_GET_DEVICE_ERRORS #define RADIOLIB_SX126X_PA_RAMP_ERR 0b100000000 // 8 8 device errors: PA ramping failed #define RADIOLIB_SX126X_PLL_LOCK_ERR 0b001000000 // 6 6 PLL failed to lock #define RADIOLIB_SX126X_XOSC_START_ERR 0b000100000 // 5 5 crystal oscillator failed to start #define RADIOLIB_SX126X_IMG_CALIB_ERR 0b000010000 // 4 4 image calibration failed #define RADIOLIB_SX126X_ADC_CALIB_ERR 0b000001000 // 3 3 ADC calibration failed #define RADIOLIB_SX126X_PLL_CALIB_ERR 0b000000100 // 2 2 PLL calibration failed #define RADIOLIB_SX126X_RC13M_CALIB_ERR 0b000000010 // 1 1 RC13M calibration failed #define RADIOLIB_SX126X_RC64K_CALIB_ERR 0b000000001 // 0 0 RC64K calibration failed //RADIOLIB_SX126X_CMD_SET_LBT_SCAN_PARAMS + RADIOLIB_SX126X_CMD_SET_SPECTR_SCAN_PARAMS #define RADIOLIB_SX126X_SCAN_INTERVAL_7_68_US 10 // 7 0 RSSI reading interval: 7.68 us #define RADIOLIB_SX126X_SCAN_INTERVAL_8_20_US 11 // 7 0 8.20 us #define RADIOLIB_SX126X_SCAN_INTERVAL_8_68_US 12 // 7 0 8.68 us #endif #endif